Brother MFC8220 Trouble Error Codes List

Brother MFC8220 Trouble Error Codes List

Code	Description	Causes
56	Front cover opened.
5A	Out of paper.
6A	Heater warming-up timeout error. (Heater does not reach 60°C within 11 sec.)	• Thermistor ASSY • Halogen lamp
6B	Heater warming-up timeout error. (Heater does not reach 100°C within 15 sec.)	• Thermistor ASSY • Halogen lamp
6C	Heater temperature exceeds the maximum high temperature. (270°C or more is detected for 1 sec.)	• Thermistor ASSY • Power supply PCB
6D	Heater temperature lowers the minimum low temperature. (60°C or less is detected for 1 sec.)	• Thermistor ASSY • Power supply PCB
6E	Heater temperature does not go up enough. (Slower temperature rise rate than 2°C/5 sec. is detected.)	• Halogen lamp • Power supply PCB
6F	Heater hard limiter operates.	• Thermistor ASSY • Power supply PCB
71	Scanner motor does not synchronize with the reference clock.	• Scanner motor
72	Cannot detect Beam Detect signal.	• Scanner motor
73	Drum unit is not mounted.	• Toner sensor • Drum unit
74	Toner empty.	• Toner sensor • Toner cartridge
75	In-casing temperature error.	• Thermistor ASSY
76	Heater harness disconnected or broken.	• Thermistor ASSY • Halogen lamp
77	Power was turned off when error 76 or error 78 occurred.

78	Heater thermistor harness disconnected or broken.	• Thermistor ASSY
79	In-casing temperature sensor harness disconnected or broken.	• Thermistor ASSY • Main PCB • Engine PCB • Main motor
7A	Main motor does not synchronize with the reference clock.
7B	ASIC error on the main PCB.
7C	Engine PCB error.
80	Paper size setting error.	• Paper width sensor • Paper size
81	Paper width sensor remains ON.	• Paper width sensor
82	Paper feeding error.	• Paper pick-up roller
83	Paper jam. Regist sensor, second regist sensor, or manual feed sensor remaining ON.	• Regist sensor • Main PCB
84	Paper jam. Paper eject sensor remaining ON.	• Regist sensor actuator • If the paper width sensor is defective, replace the needle tube & head flat cable ASSY. • Main PCB
85	No paper tray loaded.	• Paper tray
86	No 2nd paper tray loaded.	• Paper tray
87	Main motor stop position error.	• Main motor
88	Paper jam. Paper eject sensor remaining OFF even after regist sensor is turned OFF.	• Regist sensor actuator • If the paper width sensor is defective, replace the needle tube & head flat cable ASSY. • Main PCB
A1	Main cover opened.	• Main PCB • Scanner unit

A2	Document too long to scan.	• Document front sensor • Document rear sensor • Document sensor PCB • Document feed roller • ADF motor • Main PCB
A3	Document not detected by the document rear sensor.
A4	Not used. (50% or more of white level data is improper.)
A5	FAX transmission scan failure detected. First attempt.	• CIS • Main PCB
A6	FAX transmission scan failure detected. Second attempt.	• CIS • Main PCB
AA	The document cover is not closed.
AC	Less than 50% of white level date is incorrect.
AE	CIS home position sensor remains OFF. In other words, the CIS unit does not return to the home position.	• CIS • Driver PCB • Main PCB
AF	CIS home position sensor remains ON. In other words, the CIS unit remains in the home position.
B0	Scanner motor harness half inserted.	• Scanner motor harness
B1	Dark level offset data level error for scanning.	• CIS • Main PCB
B2	Gain control data level error for scanning.
B3	Scan area left edge detection error.	• CIS • Main PCB • Black markings on the white-level reference film inside the scanner top cover
B4	Scan area right edge detection error.
B7	A/D converter standard voltage failure; at High side.

B8	A/D converter standard voltage failure; at Low side.
B9	Scanning light source failure.	• CIS • Main PCB
BB	Scanning white level failure.	• CIS • Main PCB • White tape
BD	Black level data error.	• CIS • Main PCB
Dx	Modem error.	• Main PCB
E4	Out of paper.	• Regist sensor • Main PCB
E6	Write error in EEPROM.	• Driver PCB
E8	Data scanning error during transmission.	• CIS • Main PCB
EA	Document removed at phase B.
F5	EOL not found during page memory transfer.	• Replace the main PCB if this error occurs frequently.
F6	PC interface error.	• Interface cable • Main PCB
FA	Scanner motor error detected.	• Scanner motor
FF	Memory management error	• Replace the main PCB if this error occurs frequently.

Brother MFC8220 Trouble Error Codes List,Brother MFC8220,Error Code,Service Manuals, Error Code Serivce Manuals For All Copy machine And Printers,
Brother Error Code, Sanyo Error Code,Samsung Error Code,Roland Error Code, RisoError Code,
Riso Error Code, Ricoh Error Code, Panasonic Error Code, Oki Error Code,Muton Error Code,
Minolta Error Code,Mimaki Error Code, Lexmark Error Code, Kyocera-Mita Error Code,Konica Error Code, Kip Error Code,Hp Error Code, Epson Error Code, CannonError Code,
Brother Service Manuals, Sanyo Service Manuals,Samsung Service Manuals,RolandService Manuals,Riso Service Manuals,Riso Service Manuals, Ricoh Service Manuals, Panasonic Service Manuals, Oki Service Manuals,Muton Service Manuals,MinoltaService Manuals,Mimaki Service Manuals, Lexmark Service Manuals, Kyocera-MitaService Manuals,Konica Service Manuals, Kip Service Manuals,Hp Service Manuals,Epson Service Manuals, Cannon Service Manuals,